碳纤维原丝含油率测试影响因素研究

利用改进的索氏提取回流法测量碳纤维原丝含油率.研究了溶剂回流温度、回流时间、环境湿度对测试结果的影响,结果表明:随着回流温度的提高,2小时内回流清洗效果不断增强,当回流温度大于54℃,次数大于12次,油剂清洗效果基本保持不变.可通过提高回流温度以提高单位时间内的回流次数,优化纤维含油率测试的准确性和测试效率.环境湿度对索氏提取测纤维含油率有显著影响:控制环境湿度在50～52％RH范围内,可将纤维吸潮质量变化控制在纤维质量的0.005％,油剂相对含量的0.2％～0.6％,可将测试稳定差值降低至≤0.05％,测试方法差值<0.1％,满足油剂测试工艺要求.回流时间≥2 h,回流温度≥54℃,测试环境湿度50～52％RH,索氏提取回流法油剂测试误差<0.05％.     

Antioxidant Activity of Piceatannol in Canola Oil

Piceatannol has shown to be a strong antioxidant in vivo, however, its ability to suppress lipid oxidation in foods has not been examined. The present study is to examine the antioxidant effect of piceatannol on heated canola oil compared with that of butylated hydroxytoluene (BHT). The oxidation of canola oil is conducted at 60, 90, 120, and 150 °C by monitoring the depletion of oxygen, the decrease in unsaturated fatty acids, and the changes of primary and secondary oxidation products. Results demonstrated that piceatannol can suppress lipid oxidation of canola oil in a dose-dependent manner with its effect being more effective than BHT. Practical Applications: Lipid oxidation is a major factor in the deterioration of food quality. Synthetic antioxidants, such as BHT and butylated hydroxyanisole, are used to inhibit oxidation in foods, but their safety has been always concerned. Piceatannol has exhibited a strong antioxidant activity to attenuate lipid oxidation and it should be further explored for use as a natural antioxidant in foods.     

One-step preparation of the superhydrophobic Al alloy surface with enhanced corrosion and wear resistance

Corrosion and wear failures are bottlenecks for restricting applications and developments of Al-based functional materials. As a new lubrication technology, superhydrophobic preparation provides an effective way to settle Al alloy corrosion. The preparation methods of superhydrophobic Al alloys are mainly multistep strategies. In this study, superhydrophobic Al alloy, has been prepared by an efficient one-step electrochemical etching process. Meanwhile, its micromorphology has been observed by a scanning electron microscope. The wettability has been measured by video optical contact angle meter. The corrosion behavior has been tested by electrochemical workstation, and wear performance has been characterized by friction tester. The results show that the micro-nanoterraced concave–convex structure has been fabricated and an as-prepared surface exhibits excellent superhydrophobic behavior. Further electrochemical and tribological tests show that corrosion resistance and wear resistance have also been significantly improved. This study provides a new method to prepare wear-resistant and corrosion-resistant Al alloy for widening applications of multifunctional Al-based engineering materials.     

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

Configurational Isomers Induced Significant Difference in All-Polymer Solar Cells

The design of polymer acceptors plays an essential role in the performance of all-polymer solar cells. Recently, the strategy of polymerized small molecules has achieved great success, but most polymers are synthesized from the mixed monomers, which seriously affects batch-to-batch reproducibility. Here, a method to separate γ-Br-IC or δ-Br-IC in gram scale and apply the strategy of monomer configurational control in which two isomeric polymeric acceptors (PBTIC-γ-2F2T and PBTIC-δ-2F2T) are produced is reported. As a comparison, PBTIC-m-2F2T from the mixed monomers is also synthesized. The γ-position based polymer (PBTIC-γ-2F2T) shows good solubility and achieves the best power conversion efficiency of 14.34% with a high open-circuit voltage of 0.95 V when blended with PM6, which is among the highest values recorded to date, while the δ-position based isomer (PBTIC-δ-2F2T) is insoluble and cannot be processed after parallel polymerization. The mixed-isomers based polymer, PBTIC-m-2F2T, shows better processing capability but has a low efficiency of 3.26%. Further investigation shows that precise control of configuration helps to improve the regularity of the polymer chain and reduce the π–π stacking distance. These results demonstrate that the configurational control affords a promising strategy to achieve high-performance polymer acceptors.     

Optimal Design of Novel Electromagnetic-Ring Active Balancing Actuator with Radial Excitation

Imbalance vibration is a typical failure mode of rotational machines and has significant negative effects on the effii-ciency,accuracy,and service life of equipment.To automatically reduce the imbalance vibration during the opera-tional process,different types of active balancing actuators have been designed and widely applied in actual produc-tion.However,the existing electromagnetic-ring active balancing actuator is designed based on an axial excitation structure which can cause structural instability and has low electromagnetic driving efficiency.In this paper,a novel radial excitation structure and the working principle of an electromagnetic-ring active balancing actuator with a combined driving strategy are presented in detail.Then,based on a finite element model,the performance param-eters of the actuator are analyzed,and reasonable design parameters are obtained.Self-locking torque measurements and comparative static and dynamic experiments are performed to validate the self-locking torque and driving effi-ciency of the actuator.The results indicate that this novel active balancing actuator has sufficient self-locking torque,achieves normal step rotation at 2000 r/min,and reduces the driving voltage by 12.5％.The proposed novel balancing actuator using radial excitation and a combination of permanent magnets and soft-iron blocks has improved electro-magnetic efficiency and a more stable and compact structure.     

Molecular fingerprint and machine learning to accelerate design of high-performance homochiral metal–organic frameworks

Computational screening was employed to calculate the enantioseparation capabilities of 45 functionalized homochiral metal–organic frameworks (FHMOFs), and machine learning (ML) and molecular fingerprint (MF) techniques were used to find new FHMOFs with high performance. With increasing temperature, the enantioselectivities for (R,S)-1,3-dimethyl-1,2-propadiene are improved. The “glove effect” in the chiral pockets was proposed to explain the correlations between the steric effect of functional groups and performance of FHMOFs. Moreover, the neighborhood component analysis and RDKit/MACCS MFs show the highest predictive effect on enantioselectivities among the four ML classification algorithms with nine MFs that were tested. Based on the importance of MF, 85 new FHMOFs were designed, and a newly designed FHMOF, NO₂-NHOH-FHMOF, with high similarity to the optimal MFs achieved improved chiral separation performance, with enantioselectivities of 85%. The design principles and new chiral pockets obtained by ML and MFs could facilitate the development of new materials for chiral separation.     

常减压蒸馏装置常压塔顶空冷腐蚀问题分析

常压塔顶空冷的腐蚀问题是国内炼油企业常减压蒸馏装置的共性问题,针对某石化公司1000×104 t/a常减压蒸馏装置的常顶空冷问题,从工艺的特殊性开始分析,结合历年发生的腐蚀问题进行剖析,对空冷内介质进行计算,分析出空冷偏流、超速、液态水偏少等原因,并提出调整中和剂注入方式等整改措施.     

A Highly Sensitive,Reversible, and Bidirectional Humidity Actuator by Calcium Carbonate Ionic Oligomers Incorporated Poly(Vinylidene Fluoride)

Sensitivity and multi-directional motivation are major two factors for developing optimized humidity-response materials, which are promising for sensing, energy production, etc. Organic functional groups are commonly used as the water sensitive units through hydrogen bond interactions with water molecules in actuators. The multi-coordination ability of inorganic ions implies that the inorganic ionic compounds are potentially superior water sensitive units. However, the particle forms of inorganic ionic compounds produced by classical nucleation limit the number of exposed ions to interact with water. Recent progress on the inorganic ionic oligomers has broken through the limitation of classical nucleation, and realized the molecular-scaled incorporation of inorganic ionic compounds into an organic matrix. Here, the incorporation of hydrophilic calcium carbonate ionic oligomers into hydrophobic poly(vinylidene fluoride) (PVDF) is demonstrated. The ultra-small calcium carbonate oligomers within a PVDF film endow it with an ultra-sensitive, reversible, and bidirectional response. The motivation ability is superior to other bidirectional humidity-actuators at present, which realizes self-motivation on an ice surface, converting the chemical potential energy of the humidity gradient from ice to kinetic energy.